자유게시판

Repairs to upvc window repairs Windows

uPVC windows are a great choice for modern homes. They are long-lasting, durable and easy to maintain. In contrast to aluminium and timber, they don't rust or rot.

Regularly cleaning and lubricating UPVC windows and doors is crucial. This will reduce unnecessary repair costs and also improve energy efficiency.

1. Broken Glass

The broken glass in your windows could cause severe damage to your home and may even be fatal. It is essential to ensure that your windows are in good working order.

Single-pane windows are fairly simple to replace, and they generally fit into frames of the past easily. However, if you have double-pane windows that are secured by internal beading it will be more difficult to get rid of the panes that are in place and replace them with new ones. In this instance you'll need to locate some plastic spacers that aid the new pane in being able to fit properly into the window frame.

Wearing eye protection and heavy gloves is essential if you plan to remove the glass yourself. It is also an excellent idea to lay down a dropcloth before you begin working on the glass so that any fragments of glass fall onto the fabric instead of onto the floor, where they could be trampled upon and cause further damage.

Once the glass is removed, it's a good idea to seal the gap with some clear packaging tape or duct tape to block drafts and water from entering the home until a professional is able to come out and fix the window. This will also provide a barrier to prevent any intruders from getting into your home. If the gap is large, you may want to consider using the security door with an integrated window as it offers the best of both worlds.

2. Sagging

Upvc is a long-lasting energy-efficient, cost-effective and economical alternative to timber sash windows. However, over time they are susceptible to a range of problems including sliding. A window that isn't properly aligned can cause problems with light, draughts and even security. It's crucial to act immediately if you realize that your uPVC windows are falling down.

To fix a sagging window you can try repositioning the hinges. You'll first need to open the windows so you can reach the frame. With a screwdriver, you can take off the top and bottom hinges and adjust them by turning them clockwise or counter-clockwise. After you've repositioned the hinges, close the window and test it for fitting. If you are happy with the fit of the window, you can tighten screws to secure them in the right position.

If you cannot reposition the hinges, you may need to replace the seal. Rubber seals can dry out and lose their elasticity over time, leading them to loosen. If this happens, it's essential to replace the seal as quickly as possible so that your uPVC windows are watertight and draught-proof.

UPVC handles can also loosen up. Often this is due to screws that have become loose over time. However, it could occur because the handle mechanism has been worn out. It's a good thing that it's simple to repair a loose uPVC window handle yourself. First, you'll need to close the window and perform an experiment fitting. The joints at the corners of the sash must align with the joint on the casing. If it isn't you can use a screwdriver to loosen the handle. Then, you can turn the mechanism back into place.

3. Water Leaks

If you awake to wet floors and damp walls every time it rains it is important that you take action. Leaks of water from windows can cause structural damage to your home and hinder your ability to control the temperature of your home. Most of the time, uPVC window leaks are caused by damaged or missing sealant.

This is an easy fix that can be completed by any DIYer who is competent. Depending on how serious the issue is, old caulking might need to be removed. It is crucial to remember that when it is about uPVC window repairs you should avoid the temptation to "over-caulk in order to make the area harder to clean and could reduce your energy efficiency.

Make sure that the drainage holes do not have debris in them, and also that the sill pan has been properly angled to drain away from the window. In more serious situations, you might have to consider replacing the window.

Moldy sills and rotten ones are also signs of water leakage. The is a fungus that thrives in damp conditions and can quickly spread across the home.

If the leakage is occurring between the double-glazed glass it is more likely that the issue is more with the seal than the frame. A uPVC specialist can easily fix this issue by replacing the glass seal. This will restore the full insulation of your windows.

4. Faulty Hinges

If your uPVC windows are stiff to open, or are loose and blow open with a breeze, it may be the hinges that are at the fault. They can be easily repaired by any skilled DIYer and can be done within a few minutes.

Nearly every home in the UK will have either top hung or side-hung uPVC windows that have hinges and like any mechanical part they can wear down over time. Changing a window hinge is essentially a very simple process, but it's easier with someone else to assist in holding the frame up.

It is also important to ensure that the uPVC hinges are opened and closed in the correct direction. You can check this by looking for the arrows on each hinge, this indicates the direction in which the window repair should be opened.

Window hinges that aren't working properly can be caused by incorrectly opening the window in a certain way or due to poor installation at the factory. Sending us a photo via our website is often enough to solve the issue. We are always happy to provide assistance.

Regular lubrication of the hinges is also necessary. Applying a light engineering lubricant to the hinges is an ideal method of doing this. We suggest using a lubricant that does not contain solvents, like 3-in-1 Multi-Purpose oil. Regular lubrication can make the window easier to open and close. It can also prevent corrosion and reduce the risk of sticking. Ideally, you should do this at least once a year. WD40 and other solvent-based lubricants are not recommended as they could damage your uPVC windows.

5. Draughts

Draughts in windows made of upvc can be caused by a variety of various factors. Firstly the hinges, again due to wear and tear could become misaligned. This causes a gap to form where the sash meets the frame. If they are damaged beyond repair, it may be necessary to have them realigned. The interlock may be unbalanced. It is located on the hinge's side and may need to be cleaned. In some instances it might be necessary to replace them.

These seals can wear down or get damaged over time, allowing air to escape. Installing high-quality weatherstripping is a good way to keep draughts at bay. Another alternative is to replace the window with glass that is low-emissivity, which will help regulate indoor temperatures and again will lessen the risk of draughts.

The final method to cut down on draughts effectively is by using a Draught-exclusion device. These are typically fabric tubes filled with a filler which can be hung over your window sill. These will help to stop cold air from entering and keep your home warm and cozy!

Your upvc windows can keep providing excellent insulation and security to your home by performing regular maintenance and repairs. However, it is important to recognize that windows last for a certain period of time and there may come an point at which it is more cost-effective to replace them rather than fix them. If you have any problems with your window made of upvc you should consult an expert immediately.